1990 accord headlights burning out

Discussion in 'Accord' started by Jonathan Lim, Feb 7, 2004.

  1. Jonathan Lim

    Jonathan Lim Guest

    Hello,

    I'm having a persistent problem with my 1990 accord headlight bulbs.
    These bulbs have been fine for over 6 years. The other day they both
    blew out. As soon as I replaced them the bulbs blew out again. Someone
    suggested that it may be a problem with the ground wire. Anyone know
    where the ground wire is? I can't seem to find it. Or any other ideas on

    what I should check next?
     
    Jonathan Lim, Feb 7, 2004
    #1
  2. Jonathan Lim

    Randolph Guest

    Perhaps your voltage regulator is broken. Elevated operating voltages
    dramatically decrease bulb life. With the engine running and the brake
    pedal pressed you should have 14.5 V +/- 0.6 V measured at the battery,
    regardless of RPM. If the voltage rises above 15.1 V as you increase the
    RPM, the voltage regulator is broken. (Voltage numbers from '94 Civic
    service manual, doubt your Accord would be different)
     
    Randolph, Feb 7, 2004
    #2
  3. Jonathan Lim

    Randolph Guest

    Perhaps your voltage regulator is broken. Elevated operating voltages
    dramatically decrease bulb life. With the engine running and the brake
    pedal pressed you should have 14.5 V +/- 0.6 V measured at the battery,
    regardless of RPM. If the voltage rises above 15.1 V as you increase the
    RPM, the voltage regulator is broken. (Voltage numbers from '94 Civic
    service manual, doubt your Accord would be different)
     
    Randolph, Feb 7, 2004
    #3
  4. Jonathan Lim

    Randolph Guest

    Perhaps your voltage regulator is broken. Elevated operating voltages
    dramatically decrease bulb life. With the engine running and the brake
    pedal pressed you should have 14.5 V +/- 0.6 V measured at the battery,
    regardless of RPM. If the voltage rises above 15.1 V as you increase the
    RPM, the voltage regulator is broken. (Voltage numbers from '94 Civic
    service manual, doubt your Accord would be different)
     
    Randolph, Feb 7, 2004
    #4
  5. Jonathan Lim

    T. Nelson Guest


    great post--I would not have thought of that as a solution. Your advice
    makes perfect sense.

    This note is to the original poster:
    Have you recently changed the fuse related to the headlights? If so, you
    might have installed the wrong type of fuse. If you have recently changed
    the fuse, I advise you to remove it and buy a new fuse from a Honda
    dealership. Tell the service department person the year your car was
    made--type of car, etc. so that he can sell you the right type of fuse. If
    it was a used car when you purchased it, the prior owner might have
    installed the wrong type of fuse.
     
    T. Nelson, Feb 7, 2004
    #5
  6. Jonathan Lim

    T. Nelson Guest


    great post--I would not have thought of that as a solution. Your advice
    makes perfect sense.

    This note is to the original poster:
    Have you recently changed the fuse related to the headlights? If so, you
    might have installed the wrong type of fuse. If you have recently changed
    the fuse, I advise you to remove it and buy a new fuse from a Honda
    dealership. Tell the service department person the year your car was
    made--type of car, etc. so that he can sell you the right type of fuse. If
    it was a used car when you purchased it, the prior owner might have
    installed the wrong type of fuse.
     
    T. Nelson, Feb 7, 2004
    #6
  7. Jonathan Lim

    T. Nelson Guest


    great post--I would not have thought of that as a solution. Your advice
    makes perfect sense.

    This note is to the original poster:
    Have you recently changed the fuse related to the headlights? If so, you
    might have installed the wrong type of fuse. If you have recently changed
    the fuse, I advise you to remove it and buy a new fuse from a Honda
    dealership. Tell the service department person the year your car was
    made--type of car, etc. so that he can sell you the right type of fuse. If
    it was a used car when you purchased it, the prior owner might have
    installed the wrong type of fuse.
     
    T. Nelson, Feb 7, 2004
    #7
  8. Jonathan Lim

    Jonathan Lim Guest

    I haven't touched the fuses since I purchased the car - that was in '96. The
    headlights have always been fine until now. Every time I put a new bulb in
    it blows out immediately. Thanks for the tips though. I will have a look at
    the voltage regulator issue. In the meantime, any other tips or ideas would
    be greatly appreciated! Thanks!
     
    Jonathan Lim, Feb 8, 2004
    #8
  9. Jonathan Lim

    Jonathan Lim Guest

    I haven't touched the fuses since I purchased the car - that was in '96. The
    headlights have always been fine until now. Every time I put a new bulb in
    it blows out immediately. Thanks for the tips though. I will have a look at
    the voltage regulator issue. In the meantime, any other tips or ideas would
    be greatly appreciated! Thanks!
     
    Jonathan Lim, Feb 8, 2004
    #9
  10. Jonathan Lim

    Jonathan Lim Guest

    I haven't touched the fuses since I purchased the car - that was in '96. The
    headlights have always been fine until now. Every time I put a new bulb in
    it blows out immediately. Thanks for the tips though. I will have a look at
    the voltage regulator issue. In the meantime, any other tips or ideas would
    be greatly appreciated! Thanks!
     
    Jonathan Lim, Feb 8, 2004
    #10
  11. Jonathan Lim

    Im anonymous Guest

    The fuse wouldn't cause the headlights to burn out. Check the voltage
    like someone else said.
     
    Im anonymous, Feb 8, 2004
    #11
  12. Jonathan Lim

    Im anonymous Guest

    The fuse wouldn't cause the headlights to burn out. Check the voltage
    like someone else said.
     
    Im anonymous, Feb 8, 2004
    #12
  13. Jonathan Lim

    Im anonymous Guest

    The fuse wouldn't cause the headlights to burn out. Check the voltage
    like someone else said.
     
    Im anonymous, Feb 8, 2004
    #13
  14. Maybe, but it may also be that there IS a ground problem, such that both H
    and L filaments are on. This overheats the bulb and soon burns it out. With
    one new bulb, test if high and low beam switches correctly.

    Stewart DIBBS
     
    Stewart DIBBS, Feb 8, 2004
    #14
  15. Maybe, but it may also be that there IS a ground problem, such that both H
    and L filaments are on. This overheats the bulb and soon burns it out. With
    one new bulb, test if high and low beam switches correctly.

    Stewart DIBBS
     
    Stewart DIBBS, Feb 8, 2004
    #15
  16. Maybe, but it may also be that there IS a ground problem, such that both H
    and L filaments are on. This overheats the bulb and soon burns it out. With
    one new bulb, test if high and low beam switches correctly.

    Stewart DIBBS
     
    Stewart DIBBS, Feb 8, 2004
    #16
  17. If your voltage regulator is putting out enough voltage to blow the bulbs,
    it could be stressing other components which could be very costly to
    replace. You need to check that voltage soon and if that's the problem,
    get the thing fixed.

    Rgds, George Macdonald

    "Just because they're paranoid doesn't mean you're not psychotic" - Who, me??
     
    George Macdonald, Feb 8, 2004
    #17
  18. If your voltage regulator is putting out enough voltage to blow the bulbs,
    it could be stressing other components which could be very costly to
    replace. You need to check that voltage soon and if that's the problem,
    get the thing fixed.

    Rgds, George Macdonald

    "Just because they're paranoid doesn't mean you're not psychotic" - Who, me??
     
    George Macdonald, Feb 8, 2004
    #18
  19. If your voltage regulator is putting out enough voltage to blow the bulbs,
    it could be stressing other components which could be very costly to
    replace. You need to check that voltage soon and if that's the problem,
    get the thing fixed.

    Rgds, George Macdonald

    "Just because they're paranoid doesn't mean you're not psychotic" - Who, me??
     
    George Macdonald, Feb 8, 2004
    #19
  20. =====================

    If you install a halogen lamp but don't tighten it in place properly, it
    won't get the cooling it requires. I kept blowing left headlamps in my
    Caravan because previous owner had lost the locking collar, which holds
    the base of the lamp intimate on the body of the lamp housing.

    If you've put the bulb in with the base not sitting flat against the
    mating surface, it won't dissipate heat and will burn out way too soon.
    I think there's only one way for the notch in the base to align with
    place it fits into...

    'Curly'

    ================
     
    'Curly Q. Links', Feb 9, 2004
    #20
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.