Interesting ABS problem

Discussion in 'General Motoring' started by MajBach, Sep 16, 2005.

  1. MajBach

    MajBach Guest

    '96 Accord EXR, VTEC

    Hi again, My ABS is acting strangely. Recently, I noticed a peculiarity when
    coming to a stop: the ABS kicks in momentarily. To be more specific, when
    stopping with light brake pressure only, just before the car is completely
    stopped, the ABS releases the brake pressure and then re-applies it. This
    makes the car lose deceleration and then stop suddenly. IT only does this
    when using light brake pressure and at very slow speeds. However, the
    problem is significant enough to be potentially dangerous. If I am pulling
    my boat for example, I can easily misjudge where the car will halt be a foot
    or more.
    At first I thought this was related to another problem I had recently where
    one of my brake calipers came loose ( on the back of the car ); I guess I
    used to much anti-seize and didn't torque down the nuts enough. But this is
    definitely an ABS problem. I know this for certain because if I engage my
    hand-brake just enough to make the warning light come on, after about a
    minute or so, the ABS will shut off, as indicated on the dash. I know this
    to be normal. The symptoms during a stop are no longer. Releasing the hand
    brake and having the ABS come back on make the problems reappear. Does
    anyone have any thoughts?
    MajBach
     
    MajBach, Sep 16, 2005
    #1

  2. ==============================

    Your four tires are not all the same diameter. ABS is sensing a
    difference in wheel speed and applying itself. There is a TSB out there
    about a similar problem . . . Sorry, lost the hard drive, now it's
    gone:-(

    Did you search google, or take a look at Tegger's FAQ?
    www.tegger.com/hondafaq/ Look at the Accord section, and the TSB page.

    'Curly'
     
    'Curly Q. Links', Sep 16, 2005
    #2
  3. MajBach

    Elle Guest

    ??

    With some exceptions, torque specs assume no anti-seize is used. So if you
    apply anti-seize where none is specified, and then torque to the "non
    anti-seized specs," you're overtorquing the threads. Studies indicate by
    about 30% or more easily, IIRC.

    For example, see http://www.airheads.org/content/view/217/49/ :
    "The rule of thumb for tightening spark plugs,,,,in fact almost any threaded
    object, is to use about 30% less than dry specifications, when lubricated by
    antiseize compound."

    (Not that I advocate applying anything to spark plug threads!)
    I'd be in the Chilton's manual, going through the diagnostics procedures.

    I know, big help. But my Chilton's manual for 1985-1995 does have many, very
    specific diagnostic procedures for stuff like this.

    E.g. for 96 Civics with ABS features, see the diagnostic steps at
    http://www.honda.co.uk/owner/CivicManual/index.html . Might be similar for
    your Accord.
     
    Elle, Sep 16, 2005
    #3
  4. MajBach

    MajBach Guest

    Curly: an interesting diagnosis. I just woke up from a cat nap and thought I
    had the solution myself. Perhaps one or more of the teeth on the bearing
    housing that allow the computer to sense speed are broken. That's a complete
    guess though. I like your idea better (cheaper fix) and it makes sense. For
    the past several months, my car has exhibited an unusual wobble. It's
    apparent at slow speeds by a definite deflection of the steering wheel by as
    much as a half inch either direction. Oddly enough, there is no
    'out-of-balance' feel to it at highway speeds. Also noticing more recently
    (about the same time as the ABS problem), a bad pull to the left, like out
    of alignment but again, not as noticeable at faster speeds. I've had similar
    symptoms on tires with broken belts, but always a rear tire. Perhaps this
    one is on the front. Fairly new tires however. I'll look into it more. Still
    surprised that that is enough to fool ABS though.
     
    MajBach, Sep 16, 2005
    #4
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.